Nissan airbag module 28556-3KF0A – crash data reset
We clear crash data and fault codes from the Nissan SRS module 28556-3KF0A – on the bench (module removed). No prepayment; the price is confirmed before any work.
Order for module 28556-3KF0A
No prepayment. We confirm the price and turnaround by phone, and the address and courier instructions arrive by e-mail right away.
- 30–150 € depending on the module
- Back with you in 24–48 h
- No charge if the module cannot be recovered
Module 28556-3KF0A details
| Hardware part number | 28556-3KF0A |
|---|---|
| Vehicle | Nissan (SRS / airbag module) |
| Module manufacturer | BOSCH |
| Where the crash record is stored | Serial EEPROM 95320 (SPI) |
| How it is reset | On the bench (module removed) |
| Price | from 60 to 150 € depending on the module, confirmed before any work |
| Turnaround | The same or the next working day after receipt |
| Support | Full |
What we do with module 28556-3KF0A
Crash data reset
We erase the crash record so the module works again after the deployed airbags and pretensioners have been replaced.
Reading and clearing fault codes
We read the SRS module codes (B-codes), check which are active and clear them after the repair.
Module identification
We read the part number, software version and VIN so we are sure we work with the right record.
How it works for Nissan with this module
- You order through the form or by phone. You receive the address and packing instructions.
- You remove the module after disconnecting the battery and waiting 10 minutes.
- You send it by tracked courier from anywhere in the EU. We also accept an enquiry with a photo of the label.
- We connect it on the bench – we read the serial EEPROM 95320 (SPI) and make a full backup before any work. We clear the crash data and the fault codes.
- We ship it back by tracked courier the same or the next working day. On refitting, check the other control units for a stored crash.
When it is needed
- After a crash with deployed airbags or pretensioners – the module keeps the record and will not re-arm the system.
- After a lighter impact where only the belt pretensioners fired – the light stays on although the airbags are intact.
- With a used module from another vehicle that has a stored crash.
- With an imported car that arrives with an airbag light and a crash record in its history.
What a reset does NOT fix
- A damaged airbag, pretensioner or crash sensor – they set a new fault immediately.
- A broken wire or corroded connector under the seat – the most common reason for the light without a crash.
- A module with a burnt board after a short circuit – for Nissan we then source a module with the same part number and clone it.
Other Nissan airbag modules by BOSCH with 95320 memory
Same module family – handled the same way as 28556-3KF0A.
Frequently asked questions
Do I have to remove module 28556-3KF0A?
Yes. This module is handled only on the bench – it is connected directly to the board. Send it by tracked courier; we ship it back the same or the next working day. Disconnect the battery and wait a few minutes before removal.
Why is the airbag light still on after the reset?
Because crash data is not the only cause. If an airbag, pretensioner, crash sensor or connector is damaged or has not been replaced, the module logs a new fault. That is why we read all fault codes before the reset and tell you what still needs replacing.
Can you clear the crash data without replacing the airbags?
We do not. The module stores the record because the components have fired. We reset it only once the airbags and pretensioners have been replaced; otherwise the system will not protect the occupants in the next crash.
How much does the reset of module 28556-3KF0A cost?
The price depends on the method (OBD or bench) and whether there are other faults. We confirm it by phone from the part number before we start. No hidden costs – if the module is faulty and cannot be recovered, you do not pay for the attempt.